HP2-Z34 試験問題を無料オンラインアクセス

Refer to the exhibit

useOSPF
have established an MPLS domain.
use LDP.
have established a Martini Layer 2 VPN between Sites 1 and 2 VPN traffic is using the link between PE-1 and P-4, and this link fails. What happens to the VPN traffic?

• A.It fails over to the link between PE-1 and P-5 only //administrators created a backup virtual circuit (VC) from PE-1 to
• B.It fails over to the link between PE-1 and P-5. The failover is automatically handled by MPLS. LDP, and OSPF
• C.It fails over to the link between PE-1 and P-5 only if administrators created two virtual
  circuits (VCs) between PE-1
• D.It is disrupted for this particular site-to-site connection until the link is fixed
• E.and PE-2.

Refer to the exhibit

An administrator is setting up an MPLS Layer 2 VPN between customer Sites 1 and 2 and is defining the pseudo wire (PW) ID for this purpose. How should the PW IDs and router values be configured?

• A.Set the PW ID to the same value on PE-1 and PE-2. Use a different value from other PWs on these routers.
• B.Set the PW ID to the same value on PE-1 and PE-2. The value on each router must match the S-VLAN ID for the associated service instance.
• C.Set the PW ID to a different value on PE-1 and PE-2 Also use a different value from other PWs on these routers.
• D.Set the PW ID to a different value on PE-1 and PE-2 The value on each router must match the label advertised by the peer for its loopback address.

In addition to the Admin MDC, an HP Comware switch supports two MDCs: MDC 2 and MDC 3. The administrator wants to allow tenants for both MDCs to log in to CLI for their own MDC without first accessing the Admin MDC How can the administrator accomplish this goal?

• A.Define a physical port as the Management-Ethernet interface in the Admin MDC On each MDC. Configure a different IP address for this interface, and set up Telnet or SSH access through it.
• B.Define a VLAN as the MDC Management VLAN in the Admin MDC. On each MDC. createthis VLAN. Assign a port to it. Set up an IP address on it and set up Telnet or SSH access through it.
• C.Create subinterfaces for the AUX user-interface in the Admin MD Assign one of the subinterfaces to each of the MDCs. and set up Telnet or SSH access through that interface
• D.Assign a console port to each MDC Tenants can then connect their own terminal equipment to their assigned port.

Refer to the exhibit

An administrator is creating the EVI network shown in the exhibit Switches 1 and 2 are configured as ENDP servers. and Switch 3 is configured as an ENDP client to the ENDP servers. Which configuration is correct for the EVI tunnel interface on Switch 3?

• A.The source IP address is the address on the connection to the service provider; no other destination IP addresses need to be set.
• B.The source IP address is the address on the connection to the service provider; the addresses for switches 1, 2, and 4 need to be set as destinations
• C.The source IP address is the switch router ID; the addresses for switches 1. 2. and 4 need to be set as destinations
• D.The source IP address is the switch router ID; no other destination IP addresses need to be set.

An HP Comware switch supports FCoE in Fibre Channel Forwarder (FCF) mode. A switch interface Ten1/0/1 connects to a server FCoE Converged Network Adapter (CNA). The CNA transmits normal data traffic, which is tagged for VLANs 4 and 8. and storage traffic for VSAN 2, which is associated with VLAN 20. What is a correct port type and VLAN configuration for Ten 1/0/1?

• A.a hybrid port that has PVID 1 and defines VLANs 4 and 8 as tagged
• B.a hybrid port that has PVID 1. defines VLAN 20 as untagged, and defines VLANs 4 and 8 as tagged
• C.a trunk port that has PVID 20 and permits VLANs 4. 8. and 20
• D.a trunk port that has PVID 1 and permits VLANs 4. 8. and 20