HP0-Y37 試験問題を無料オンラインアクセス

You want to add HP edge switches to a company's Cisco network. Distribution Cisco switches are set as the Rapid PVST+ root and secondary root. You connect HP A-Series switches that are running their factory default configuration to the two Cisco distribution switches. What will happen?

• A.Cisco distribution switches send tagged PVST+ BPDUs to the HP switch. Because 802.1q is
  not yet configured on HP switch uplinks, the PVST+
  BPDUs are dropped. A loop occurs.
• B.Cisco distribution switches send untagged standard BPDUs to HP switch in VLAN 1, which the
  HP switch forwards to the other distribution
  switch, preventing a loop. The HP switch drops all tagged data frames.
• C.Cisco distribution switches send untagged standard BPDUs to the HP switch in VLAN 1, and in
  response the HP switch blocks one of the uplinks
  on all VLANs, preventing a loop.
• D.If you connect the edge switch with a redundant link to both distribution switches, you create a
  loop and a broadcast storm on the Cisco network.

Click the Exhibit button and view both exhibits.


Which configuration is valid for Switch 4?

• A.rrpp domain 2 control-vlan 3001 protected-vlan reference-instance 0 to 16 ring 1 node-mode transit primary G1/0/5 secondary G1/0/4 level 1
• B.rrpp domain 2 control-vlan 3000 protected-vlan reference-instance 0 to 16 ring 1 node-mode master primary G1/0/4 secondary G1/0/5 level 1
• C.rrpp domain 2 control-vlan 3001 protected-vlan reference-instance 0 to 16 ring 1 node-mode transit primary G1/0/4 secondary G1/0/5 level 1
• D.rrpp domain 2 control-vlan 3000 protected-vlan reference-instance 0 to 16 ring 1 node-mode transit primary G1/0/5 secondary G1/0/4 level 1
• E.rrpp domain 2 control-vlan 3001 protected-vlan reference-instance 0 to 16 ring 1 node-mode master primary G1/0/4 secondary G1/0/5 level 1

A company's Cisco network runs VTP. VTP is set in Server mode on distribution switches and in Client mode on edge switches. To prepare for the insertion of HP switches at the edge of the company's network, what should you do?

• A.Configure Cisco switches in VTP Server mode and HP switches in GVRP.
• B.Change VTP mode to Transparent on all Cisco switches.
• C.Set GVRP on all Cisco switches.
• D.Remove VTP on all Cisco switches and reconfigure all static VLANs on all switches.

Click the Exhibit button.
A provider of MPLS services configures MPLS Layer-3 VPN services for two customers. Each customer has three branch offices that will be interconnected by MPLS Layer-3 VPNs. The address blocks chosen by the customers for each site are shown in the following chart: The provider uses OSPF as its IGP with the Loopback 0 addresses shown as the OSPF router-id and the MPLS LSR-ID. Router PE-1 can ping internal networks at Cust-A site #1; however, no other PE router can ping Cust-A site #1. The routing table of Cust-A site #1 includes all other Cust-A sites. Which commands on PE-1 are most likely to resolve this problem?

• A.Option D
• B.Option E
• C.Option B
• D.Option C
• E.Option A

Click the Exhibit button.

Which statements are true about the BGP configuration of this HP A-Series router? (Select two.)

• A.Prefixes originating from AS 200 are set with local preference 200.
• B.The BGP router is in AS 200.
• C.All prefixes are set with a local preference of 100.
• D.The BGP neighbor is in AS 100.
• E.The BGP router filters prefixes 200.X.X.X.