350-601 試験問題を無料オンラインアクセス

An engineer is configuring a vHBA template in UCS Manager. The engineer needs to specify the logical addresses used by the vHBA and the path through which the SAN traffic flows.
Which two resources must be specified in the vHBA template? (Choose two.)

• A.MAC addresses
• B.WWNN
• C.Fabric ID
• D.VLAN ID
• E.WWPN Pool

Refer to the exhibit. An engineer must monitor ingress traffic from SW1 and SW2 port-channel interfaces from SW3. Which configuration must be implemented to accomplish this goal?

• A.SW3# configure terminal
  SW3(config)# monitor session 2
  SW3(config-monitor)# source interface port-channel 1 rx
  SW3(config-monitor)# source interface port-channel 2 rx
  SW3(config)# interface ethernet 1/4
  SW3(config-if)# switchport monitor
  SW3(config-if)# exit
  SW3(config)# monitor session 2
  SW3(config-monitor)# destination interface ethernet 1/4
• B.SW3# configure terminal
  SW3(config)# source interface port-channel 1 rx
  SW3(config)# source interface port-channel 2 tx
  SW3(config)# interface ethernet 1/4
  SW3(config-if)# destination interface ethernet 1/4
  SW3(config-if)# exit
  SW3(config)# interface Port-channel 1-2
  SW3(config-if)# switchport monitor
  SW3(config-if)# exit
• C.SW3# configure terminal
  SW3(config)# monitor session 2
  SW3(config-monitor)# source interface port-channel 1 tx
  SW3(config-monitor)# source interface port-channel 2 tx
  SW3(config)# interface Port-channel 1
  SW3(config-if)# switchport monitor
  SW3(config-if)# exit
  SW3(config)# interface Port-channel 2
  SW3(config-if)# switchport monitor
  SW3(config-if)# exit
• D.SW3# configure terminal
  SW3(config)# monitor session 2
  SW3(config-monitor)# source interface port-channel 1 tx
  SW3(config-monitor)# source interface port-channel 2 rx
  SW3(config)# interface port-channel 1
  SW3(config-if)# switchport monitor
  SW3(config-if)# exit
  SW3(config)# interface port-channel 2
  SW3(config-if)# switchport monitor
  SW3(config-if)# exit

What is a recommended design choice in a topology for multipathing iSCSI traffic?

• A.dual initiators to a single target with bonded interfaces
• B.two NICs bonded together on the initiator
• C.single initiator to dual targets
• D.initiators and targets in separate subnets

A network engineer needs a tool to automate the provisioning of Cisco UCS Service Profiles. The administrator has limited programming knowledge but is skilled with scripting tools. The tool must include existing support for Cisco UCS configuration. Additionally, the administrator will eventually use the solution to manage Cisco UCS C-Series Rack Servers.
Which tool meets these requirements?

• A.Python scripts
• B.PowerShell
• C.Cisco DCNM
• D.Bash scripts

An engineer must configure an ERSPAN session on a Cisco Nexus 9000 Series Switch. The mirrored traffic originates from the remote IP address 10.10.10.10 and must be forwarded to a network analyzer connected to Ethernet1/10 on the Nexus switch. Which configuration accomplishes this goal?

• A.monitor session 1 rx
  source interface all rx
  destination interface ethernet1/10
  no shut
• B.monitor session 1 type erspan-destination
  erspan-id 1
  source ip 10.10.10.10
  destination interface ethernet1/10
  no shut
• C.monitor session 1 type erspan-source
  erspan-id 1
  source ip 10.10.10.10
  source interface ethernet1/10
  no shut
• D.monitor session 1 rx
  source ip address 10.10.10.10
  destination interface ethernet1/10
  no shut